Motors & Drivers

25GA310 DC Deceleration Micromotor DC12V Label Machine Paper Output

specification:Product NameDC Geared MotorModel Type25GARated VoltageDC 12VCurrent60mASpeed50RPMShaft Size4 x 10mm/ 0.16" x 0.39" (D*H)Total Size25 x 68mm / 0.98" x 2.7" (Max.D*H)Main ColorSilver ToneM..

12.00 JOD

3CH Digital Multi Servo Tester

Output: ≤15mA (5.0)Input: DC 4.2-6.0vOutput signal: 1.5ms ± 0.5msSize: 46 * 32 * 17MMWeight: 8gAdjustment modes: manual, automatic, and the median.Features: can be easily detected and set the dummy bi..

4.00 JOD

A4988 RAMPS Pololu StepStick stepper motor driver with Heat Sink

1) Simple step and direction control interface2) Full-step, Half-step, Quarter-step, Eighth-step, and Sixteenth-step3) Adjustable current control4) Intelligent chopping control5) Over-temperature ther..

3.50 JOD

CNC Shield V3 A4988 Controller for RAMPS1.4 Reprap 3D Printer

SunRobotics CNC shield v3 A4988 Controller for RAMPS 1.4 Reprap 3D Printer & GRBL CompatibleGRBL 0.8c compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into ..

8.50 JOD

DC 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Test Module

100 brand new and high quality Diameter:28mm/1.10 inch Length:274mm/10.79 inch Step angle:5.625 x 1 / 64 Reduction ratio:1 / 64100 brand new and high qualityDiameter:28mm/1.10 inchLength:274mm/10.79 i..

5.00 JOD

Double BTS7960 43A H-bridge High-power Motor Driver module/ diy smart car Current diagnostic

Double BTS7960 43A H-bridge High-power Motor Driver module/ diy smart car Current diagnostic(B3B3)BTS7960B H-bridge 43A high-power motor driver Module Overview:This driver uses chips BTS7960 composed ..

17.00 JOD

GA12-N20 geared motor, 3V6V12V electronic lock with 10mm dc geared motor 3V 6V or 12V

6V 30RPMProduct DescriptionSpecification:Brand new & high qualityVoltage: 6VMaterial: MetalModel: N20Revolving Speed: 30RPMTotal Length: 36mmMotor Size: 12mm(diameter)*26mm(height)Shaft Size: 3mm(..

7.00 JOD

Intelligent Car Gear Motor with cable

Product description100% brand new and high qualityOperating voltage: 3V~12VDC (recommended operating voltage of about 6 to 8V)Maximum torque: 800gf cm min (3V)No-load speed: 1:48 (3V time)The load cur..

2.50 JOD

L298N DC Dual H-Bridge Module

the L298N driver module, using ST L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easi..

3.50 JOD

Metal Gear Servo MG996R 180 degrees

The MG996R is a digital metal gear servo with high torque and can be used for just about any application. It is an upgraded version of the MG995 servo with a new control system which makes the servo m..

14.00 JOD

MG90S Metal Gear Servo for Arduino Micro Tower Pro 180 Degrees

MG996R is an upgraded version of MG995 servo.The new PCB and IC control system which makes it far more accurate.Its internal gearing and motor are also upgraded to improve dead bandwidth and centering..

8.00 JOD

MG995 180 Degrees Metal Gear High Torque Servo

About Product:model: MG995Size 40.7 * 19.7 * 19.7 mmweight 55 g/ 1.94 ozReaction speed: 13 kg/cm Sperating torque: 53-62 r/M use temperature - 30 ~ 60 °Dead Band Width: 4usecPlug type JR, FUTABA ..

14.00 JOD

MG995 360 Degrees Metal Gear High Torque Servo

About Product:model: MG995Size 40.7 * 19.7 * 40.7 mmweight 55 g/ 1.94 ozReaction speed: 13 kg/cm Sperating torque: 53-62 r/M use temperature - 30 ~ 60 °Dead Band Width: 4usecPlug type J..

16.00 JOD

Micro 140 R140 DC toy motor DIY small productions Motor 3V to 6V

Length: 25mmDiameter:21mmAxis:9mm longVoltage: 3-6v 2mm shaft diameter25*21*9mm..

2.50 JOD

Nema17 1.8 degree high torque 42*42*40mm Stepper Motor

Product Description:  42 Two-phase Stepper Motor Machine Length: 48mmdiameter of axle: 5mmLength of axis: 24Static Torque:5.0kg.cm ,70 oz.in Wiring: black and g..

16.00 JOD
Showing 1 to 15 of 18 (2 Pages)